• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Making RNA probes for in situ hybridization

        互联网

        842

         

        Make DNA templates via PCR

        Day 1

        It's preferable to start with constructs that contain RNA polymerase start sites (T3, T7, or SP6) which allow use of primers outside the start-point. This gives the enzyme some docking space, improving transcription efficiency. If this is not possible, use extended primers with RNA-polymerase start sites in their 5' tails.

        Purify PCR products with QiaQuick PCR purification kit and resuspend in nuclease free water.Make DNP-NTP mixture (if needed)

        Day 1

         

           Amount  Final concentration
         Sigma H20   5.7 μl  
         ATP 100mM   2 μl  10 mM
         CTP 100mM   2 μl  10 mM
         GTP 100mM  2 μl  10 mM
         UTP 100mM  1.3 μl  6.5 mM
         DNP-11-UTP 10mM  7.0 μl  3.5 mM

         

        In vitro transcription reaction

        Day 1

         

        Heat 10X Buffer to dissolve salts before using.

        Incubate at 37oC for 2-4 hours.

        Eliminate template

        Day 1

        Add 1 μl DNAseI (RNAse free) to each reaction.

        Incubate for 15 min at 37oC. This is a time sensitive step.

        Precipitate probes

        Day 1 (immediately after eliminating the template)

        Bring reaction to 50μl with RNAse free water.

        Add 1/10th volume 3M NaOAc pH5.2 (5μl)

        Add 2.5 volumes of 100% EtOH (125μl)

        Store at -20oC for at least 2 hours.

        Spin 20 min at 4oC at 13200 rpm.

        Remove supernatant.

        Pellet for DIG/biotin reactions will be white, DNP reactions will be yellow and FITC reactions will be orange.

        Add 250-400μl 70% EtOH and spin 20 min at 4oC at 13200 rpm.

        Remove supernatant and repeat wash with 100% EtOH.

        For a 20μl reaction with a visible pellet, it is usually sufficient to dissolve the pellet directly in 100μl 50% formamide.

        If necessary: resuspend probes in 50 μl of RNAse free water. Take 5 μl for quantitation. Then add 45 μl

        100% formamide and store at -20oC.

        For 10μl reaction : with visible pellet, it is sufficient to dissolve them directly in 50μl 50% formamide in RNAse free water.

        Properly dissolved probes that have sufficiently high concentrations typically foam a lot. It will take a couple of minutes to dissolve a probe.

        Making RNA probes for in situ hybridization page 2of 2

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序