互联网2013-11-13
1. First Step: Find your DNA concentrations. The first person to nanodrop needs to get some water, TE, and a 2 ul pipette, tips and your DNA samples completely mixed. If you had a large pellet you will probably want to dilute the samples 1 to 10 before nanodropping. As you wait for the nanodrop- determine how you will organize your samples among the 16 lanes by beginning to fill out Table 1 below. This chart is explained more completely in further sections. You should have two trials for each of your samples and in one of your tubes you should have a no DNA sample in which you use water instead of DNA. Once you get to the nanodrop you can fill in your concentrations and purities.
2. Once you have your concentration. The second step will be to determine how much of each DNA to put into a PCR tube. We are going to be doing 20 ul reactions and with all of the other ingrediants, there is room to put only 8.4 ul of DNA into each tube. If possible I would like you to have 100 ng of DNA in each PCR tube. Many times your concentrations are so large that you would only have to pippette 0.1 ul of DNA ot make 100 ng. If this is the case you would need to do a dlution. Just for your info I filled out the chart and determined that if you diluted your concentration to 11.9 ng/ul, then you would use 8.4 ul of sample to give you 100 ng ie 11.9 ng/ul *8.4 ul -= 99.6 ng. You can dilute to whatever concentration you want as long as you don't use more than 8.4 ul to get 100 ng of sample. If you use less than 8.4 ul you will need to replace the rest of that volume with water to make a total of 8.4 ul.
3. To avoid a lot of pippetting when you do PCR you set up a master mix. This mix will contain the sybr green dye, Taq, nucleoties and buffer that you need for your PCR( all this comes premixed from BIORAD and is called PCR Supermix) and your two primers which were ordered from a company called Integrated DNA Technologies. I tell that company the sequence I want the primer to be and they make it and send it to me. It costs 25 cents a base to make enough primer to do these reactions in about 2 years of classes. As you can see below for a 20 ul reaction, 11.6 ul will be your Master Mix and 8.4 ul will be the DNA from above to make 20 ul total. Make sure you understand the calculations on the chart below and how I got them for the ul to use for a single reaction.
4. After you finish filling your charts out - check with your lab instructor before continuing. Once your dilutions are approved please begin making them up.
5. Label your two strips of tubes so you know which is which. Make your master mix. Make sure you vortex and spin down master mix and all of the ingrediants that make it up before you pippette them to ensure they are well-mixed up. Place 11.6 ul of master mix into each tube. Make sure you pipette the mix to the bottom of the tube as I don't have any way of spinning these strips. Keep strips on ice as much as possible.
6. Place the appropriate amount of DNA and water in each tube. Pipette into the liquid already in the tube. Use careful pipetting and mix up and down while pipetting.
7. Keep your samples on ice until we are ready to load the machine. Once they are loaded I will talk to you more about what real-time PCR is specifically compared to PCR.
相关产品推荐
Biolife Green I, 10,000× in DMSO（PCR级）
￥1840
定量PCR专用反转录试剂盒primeScript™ RT Master Mix (Perfect Real Time)
￥1600
HiFi PCR Mix for NGS，阿拉丁
￥447.90
UltraSYBR一步法荧光定量PCR试剂盒，High ROX，阿拉丁
￥1797.90
2×常规PCR预混液（含染料），2×，阿拉丁
￥92.90
相关问答
问
real time RT-PCR如何保证重复性
real time 实时荧光定量PCR
real-time PCR 与 reverse-transcription PCR 有什么区别？
相关方法
Real-time PCR（基本方法二）
2023-02-25
🔥 Real-time PCR（基本方法一）
2023-05-26
PCR
2024-05-14
推荐阅读
real time PCR primers-Real-Time PCR
Essentials of Real Time PCR
contamination in real-time pcr-Real-Time PCR
