• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Inverse PCR

        互联网

        2209

        Isolate partially purified chromosomal DNA using a modification of the Magic MiniPreps DNA Purification System from Promega (see atta ched) as follows.

        - Spin down 500 μl of an overnight culture in a 1.5 ml microfuge tube.

        - Resuspend in 200 μl of

        Tris-HCl 10 mM, pH 8.0

        & #9; EDTA 20 mM

        Sarkosyl 1%

        with 5 μl of RNaseA 10 mg/ml

        - Incubate at 65°C for 10 minutes.

        - Add 1μl of 20 mg/ml proteinase K an d incubate at 65°C for 30 min. to 1 hour.

        - Add 30 μl ammonium acetate 7.5 M.

        - Add 1 ml resin from the kit (see step V from the Promega instructions). Add to column, elute, wash and dry according to manufac turer''s instructions.

        - Elute the DNA twice with 50 μl 65°C TE.

        - Estimate the yield of DNA by running samples on an agarose gel.

        - For the inverse PCR, digest 1-5 μg of DNA with the app ropriate enzyme (PstI or KpsI for Tn5).

        - Make sure the DNA was digested to completion by runing an agarose gel with 2/10 vol. of the reaction.

        - Phenol-chloroform extract, precipitate and use 0.5 μg digested DNA for the ligation.

        - Ligate under conditions favoring intramolecular ligation: use 0.5 μg DNA in a total volume of 500 μl. Ligate O/N with 5 μl ligase at 15°C.

        - Purify the ligated DNA by elution through a G-50 column.

        - Do a PCR reaction using 25 μl of the ligation reaction and 200 pmol of each pimers (R3 and L7) in a final volume of 100 μl.

        - Since the primers will hybridize to IS50R and IS50L, there should t heoretically be two PCR products. This is not always the case. If the restriction site is either too close or too far from one of the IS50s, the intramolecular ligation or the PRC reaction may not work. In most cases, at least one product is obtained. If not, another restriction enzyme should be tried.

        - Purify the PCR fragment(s). If there is a good yield, direct sequencing of the PCR fragment(s) can be done using primer R3. Alternatively, the PCR product can be cloned before sequencing. In this case, I like to cut it first with the restriction enzyme. This will give one product of predicted size (from the L7 oligo to the restriction site in Tn5) and another fragment wich will contain the chromosomal DNA and the R3 oligo se quence (see figure).

         

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序