• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        PREPARATION OF PLASMID DNA FOR SEQUENCING

        互联网

        1149

        The following protocol is based on our modifications of R. Kraft, J. Tardiff, K. S. Krauter, and L. A. Leinwand. Biotechn . 6(6):544-545, 1988.

        Inoculate 2-5 ml of L broth containing the appropriate antibiotic from a single bacterial colony. Incubate at 37℃ overnight with vigorous shaking.

        Follow the Plasmid Quick Prep protocol through the potassium acetate step to isolate plasmid DNA.

        Add DNAse-free RNAse to 50µg/ml, incubate, 37℃ from 10-30 minutes.

        Phenol extract the solution, saving the upper aqueous phase. Ether extract the remaining phenol, and ethanol precipitate the DNA. Resuspend the pellets in 16.8 µl H2O, 3.2 µl 5 M NaCl, 20µl 13% PEG 8000, and incubate on ice for 30 min. Spin in a microfuge for 10 min, 4℃, and rinse the pellets once with 70% ethanol. Respin the pellets for 1 min and dry under vacuum.

        Resuspend pellets in 20µl H 2 O and 2 µl (1/10 volume) of a solution of 2 N NaOH and 2 mM EDTA. The original protocol called for a 5 min room temperature incubation, others incubate 30 min @ 37℃, and Darise Farris reports good results at 85℃ for 5 min then cooling on ice.

        Neutralize with 1/10 volume of 3 M sodium acetate (pH 4.5-5.5) [or add 8 µl of 1 M Tris-HCl (pH 4.0-4.5), 3 µl of 3 M sodium acetate (pH 5.2)], and 75 µl of cold ethanol. Incubate on dry ice for 20 min.

        Centrifuge at room temperature or 4℃ in a microfuge for 5 min. Discard the supernatant and wash the pellet with 70% ethanol and centrifuge 2 min. Discard the supernatant and dry the pellet under vacuum.

        Resuspend the pellet in 7 µl H 2 O, 1 µl of pUC (or the appropriate) primer at a 0.5 pmol/µl stock concentration, and 2 µl of 5x Sequenase buffer. Mix and centrifuge to remove any debri. Heat 2 min, 65℃ and cool slowly to below 35℃ by removing the heat block with samples in it from the heater to the lab bench. This cooling typically takes 30-45 min. Thaw the isotope during this time. Place tubes on ice when they reach 35℃.

        Follow the Sequenase protocol from this point. Darise Farris recommends the following modifications for optimizing for short sequences: dilute the labelling mix 1:20 instead of 1:5, add 1 µl of Mn buffer (0.15 M sodium isocitrate & 0.1 M MnCl2 ) at the annealing step, and incubate the stop reactions for 15 min instead of 5 min.

        RECIPES

        L Broth (LB; Luria-Bertani)

        10 g tryptone

        5 g yeast extract

        5 g NaCl

        1 L water

        Autoclave

        RNAse (10 mg/ml)

        Dissolve RNAse A in water. Boil for 5 minutes. Store at -20℃. Some protocols also add an equal volume of 40% glycerol and a half volume of 0.5 M NaCl.

        5 M Sodium Chloride

        73.06 g NaCl

        Add NaCl gradually to 200 ml H2 O. QS to 250 ml with water and autoclave.

        3M Sodium Acetate, pH 5.5

        18.46 g sodium acetate

        Adjust pH with glacial acetic acid (>8 ml), QS to 75 ml with water and autoclave.

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序