• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构：
    • 成为企业机构
    • 个人用户：
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Sequencing Double-Stranded DNA Using the Sequenase Version 2.0 Kit

        互联网

        1077

        实验步骤

         

        1. Prepare the DNA for sequencing as per the protocols, "Purification and Concentration of Aqueous DNA Solutions" and "Alkali Denaturation of Supercoiled Plasmid DNA".

        2. Warm a heating block up to 65 degrees.

        3. For each sample to be sequenced, put the following in a 1.5 ml Eppendorf tube:

        DNA (prepared as discussed) 7 ul

        Sequencing primer 1 ul

        Reaction Buffer 2 ul

        4. Heat to 65 degrees for 2 minutes, then remove heating block from heat source and allow to slowly cool to <35 degrees. Heating the DNA separates the strands and allows the primer to anneal as the temperature slowly declines.

        5. While cooling, prepare the following mixtures. Prepare slightly more than you actually need, in order to avoid problems during the actual procedure.

        6. Also at this time, prepare the microtiter dish that will be used during the termination reactions. Transparent tape should be applied over any wells that will not be needed, in order to provide a better seal against water leaking into the sample wells. The horizontal rows should be labelled A-T-G and C, while the vertical columns should be labelled with a code for your samples. When this is complete, place 2.5 ul of the appropriate ddNTP Termination Mix into each respective well. Use the appropriate set of Termination Mix tubes for either dGTP reactions (red-capped tubes) or for dITP reactions (green-capped tubes).

        Be sure the drop of Termination Mix makes it to the bottom of the well by tapping the plate upon the bench. Keep the plate loosely covered with a plate sealer until needed.

        7. Once the annealed template-primer has reached 35 degrees or lower, add 5.5 ul of the Master Mix by pipetting it onto the side of the sample tube and tapping it down to mix thoroughly. Before adding the Master Mix, it is a good idea to briefly spin down the samples to recover any solution clinging to the top or sides of the tube.

        Try not to contaminate the pipet tip with any sample, as it can be used to add Master Mix to all sample tubes, minimizing the amount of solid radioactive waste generated.

        8. Incubate at room temperature for 1 minute to allow for primer extension and labelling.

        9. Pipet the labelling reaction up and down to mix, and add 3.5 ul to each of the four wells on the microtiter plate containing the four termination mixes. One pipet tip can be used to add the reaction mix to the four wells by pipeting the sample onto the side of the well. The plate is then tapped on the bench causing the labelling reaction to mix with the termination mix. This procedure, once again, minimizes the amount of solid radioactive waste generated.

        10. Once all the reactions have been added to the termination mixes in the plate, cover the plate tightly with a plate sealer and place in a water bath at 37 degrees for 5 minutes.

        The water in the bath should be high enough to bubble around the wells when you look under the plate. During this step the chains are extended a little more and then terminated by the addition of a dideoxynucleotide.

        11. Wipe off the water from the outside of the plate with a Kimwipe and carefully remove the plate sealer, making sure that no drops of water fall into the wells.

        12. Add 4 ul of Stop Solution to each well by depositing the drop on the side of the well and tapping to mix.

        13. Samples may be stored, covered, at -20 degrees for up to 1 week before running on a gel.

        ad image
        ad image

        相关产品推荐

        Sequenase 版本 2.0 DNA 聚合酶

        Sequenase 版本 2.0 DNA 聚合酶

        询价

        Anti-CD204 [2F8 (recombinant version)]

        Anti-CD204 [2F8 (recombinant version)]

        ￥46647

        100 bp DNA分子量标准(100bp DNA Ladder)

        100 bp DNA分子量标准(100bp DNA Ladder)

        ￥180

        SARS-CoV-2 (2019-nCoV) Nucleocapsid/N Antibody Titer Assay Kit | SARS-CoV-2 (2019-nCoV) Nucleocapsid/N Antibody Titer Assay Kit

        SARS-CoV-2 (2019-nCoV) Nucleocapsid/N Antibody Titer Assay Kit | SARS-CoV-2 (2019-nCoV) Nucleocapsid/N Antibody Titer Assay Kit

        ￥5000

        32/32蛋白Recombinant Enterobacteria phage T4 Single-stranded DNA-binding protein (32)重组蛋白(SSB protein)(Gp32)(Helix-destabilizing protein)蛋白

        32/32蛋白Recombinant Enterobacteria phage T4 Single-stranded DNA-binding protein (32)重组蛋白(SSB protein)(Gp32)(Helix-destabilizing protein)蛋白

        ￥2616

        相关问答

        问

        pierce albumin depletion kit

        165 围观
        2024-09-14

        问

        ROB2.0的excel宏表怎么用

        2 回答 1291 围观
        2022-10-23

        问

        CRISPR CAS9质粒 T7E1 sanger sequencing TAcloning

        2 回答 592 围观
        2022-07-13

        相关方法

        使用 HC ExpressArray Kit 进行杂交与检测实验

        流式细胞术检测检测胎肝 Lin-c-Kit+Sca-1+细胞数

        DNA

        推荐阅读

        Dideoxy Sequencing Reactions Using Sequenase Version 2.0

        DNA Sequencing Using Sequenase Version 2.0 T7 DNA Polymerase

        Sequencing Double-Stranded Linear DNA with Sequenase and [α-35S] d.ATP

        无忧采购 轻松科研

        无忧采购 轻松科研

        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序