• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        3'RACE PCR

        互联网

        1931
         

        3'RACE PCR

        3' R apid A mplification of c DNA E nds (RACE ) PCR

        This technique is used to obtain the 3'end of a cDNA, it requires some sequence information internal to the mRNA under study. The sequence information obtained from this technique can be utilised to obtain full length cDNA clones using the 5'RACE technique.

        The method I've used is loosely based on that given in 'PCR protocols: A guide to methods and applications', Academic Press Inc.

        The protocol given uses SuperScript II reverse transcriptase (Life Technologies) and Taq polymerase from Boehringer Mannheim. You will need to adjust the reagents according to the enzymes you use.

        Reagents:

        Sterile water (high purity, RNase-free)
        5 x SuperScript RTase buffer (Life Technologies)
        100mM DTT
        2.5mM dNTPs
        RNase inhibitor (Pharmacia)
        SuperScript RTase (Life Technologies)
        10 x PCR buffer (Boehringer Mannheim, contains 15mM MgCl2 )
        500mM dNTPs
        Mineral oil
        RNA : Both total and polyA RNA are suitable for this technique. I recently compared the two and found the polyA RNA reaction to have the edge, but only just. I do recommend using polyA RNA for 5'RACE though.
        Primers:-
        T17 Adapter primer (T17AP): GACTCGAGTCGACATCGATTTTTTTTTTTTTTTTT
        Adapter primer (AP): GACTCGAGTCGACATCG
        Gene specific primer: Designed from known sequence, ideally it should an 18-22-mer with an annealing temperature of around 56°C, where a G/C = 4°C and an A/T = 2°C.

         

        Protocol

        1. Place approx. 1ug of total RNA (~10ng polyA RNA) in an RNase-free eppendorf, make up to 10ul with pure water. Add 1ul of T17AP (0.5ug/ul).

        2. Heat this to 70°C for 10 minutes, then place on ice for 5 minutes.

        3. Spin pulse the tube and then add the following reagents:

        4ul 5X SuperScript RTase buffer
        2ul 100mM DTT
        1ul 2.5mM dNTPs
        1ul RNase inhibitor
        1ul SuperScript RTase.

        4. Mix and incubate at 37°C for 2 hours.

        5. Use a serial dilution of the reverse transcription reaction: 2ul of undiluted cDNA, 2ul of 10 x diluted cDNA and 2ul of 100 x diluted cDNA in the PCR reaction. Set up the PCR as follows:

        35.5ul pure water
        5ul 10 x PCR buffer (Boehringer Mannheim)
        5ul 500uM dNTPs (some enzymes require a higher concentration of dNTPs (2mM), for example Pfu polymerase (though I'd recommend against the use of this enzyme)
        1ul Adapter primer (25uM)
        1ul Gene specific primer (25uM)
        2ul cDNA template (various dilutions)

        6. Mix and overlay with mineral oil.

        7. Perform the following PCR cycles:

        a. 94°C 3 minutes
        b. 72°C 3 minutes (at this point add 0.5ul of Taq polymerase)
        c. 94°C 30 seconds
        d. 56°undefined 1 minute
        e. 72°C 2 minutes (longer if expected fragment size is greater than 2kb)
        f. Cycle steps c. - e. 35 times
        g. 72°C 10 minutes.

        8. Load all or part of the reaction on an agarose gel. Don't be too surprised if you get a faint background smear as well as your prominent band.

        <center> <p>  </p> </center>
        上一篇:PCR-SSCP技术   下一篇:5&#39; RACE for EST Production
        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序