• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Prehybridization and probe labeling

        互联网

        818

         

        Prehybridization

        1. Set hybridization oven to 65°C.
        2. Thaw 32 P isotope in hood.
        3. Place membrane in hybridization tube.
        4. Add 50 mL of prehybridization buffer to each tube.
          Prehybridization buffer [for 4 probes]
          ddH2 0
          125 mL
          20X SSPE
          60 mL
          100X Denhardt's solution
          10 mL
          20% SDS
          5 mL

          Salmon sperm DNA [10 mg/mL; boil for 5 minutes and set on ice 5 minutes before adding]

          1 mL
          TOTAL
          200 mL
        5. Prehybridize membranes for at least 6 hours to overnight.

        Probe labeling

        1. Heat water to boiling in a beaker on a hot plate.
        2. Labeling components are
          Labeling components
          DNA
          1.0 µL [20�50 ng]
          ddH2 0
          4.0 µL [total volume of H2 0 and probe = 5 µL]
          Oligo primers
          1.0 µL
          dNTPs [5 mM]
          1.5µL

          Klenow polymerase

          1.0 µL
          10X Klenow buffer
          1.5µL
          dCTP 32 P
          5.0 µL
          TOTAL
          15.0 µL
        3. Conbine ddH2 0, oligo primer, and DNA in a 1.5-ml microfuge tube, boil for 4 minutes, and place on ice.
        4. Add dNTPs, 10X buffer, Klenow enzyme, and 32 P. Mix, spin briefly, and allow reaction to go overnight at room temperature or place at 37°C for 2 hours.

        Column preparation

        1. Add glass wool to the base of a 1-mL syringe and place in a 15-mL centrifuge tube.
        2. Using a transfer pipet, fill the syringe with a solution of Sephadex G-50 in TE. Avoid getting air bubbles in the column.
        3. Centrifuge tubes for ~30 seconds, refill tubes with fresh Sephadex G-50 solution, and centrifuge at 1,500 RPM for 4 minutes.
        4. Add 200 µL of TE to each column and centrifuge for 4 minutes at 1,500 RPM.

        Probe purification

        1. Add 185 µL of TE to each probe.
        2. Cut the cap off the tube and withdraw all of the probe solution from the tube with a pipet. Place an empty tube under the syringe and add the probe to the top of the column.
        3. Spin the column for 4 minutes at 1,500 RPM.
        4. Discard the column; remove tube with pruified probe and recap.
        5. Add a cap-lock to the tube, boil for 4 minutes, and place on ice.

         

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序