产品封面图

R1/E

收藏
  • 询价
  • 2025年11月20日
    avatar
    15金牌会员
  • 企业认证

    • 详细信息
    • 询价记录
    • 文献和实验
    • 技术资料
    • 年限

      3.5 days embryo, blastocyst

    • ATCC Number

      SCRC-1036™

    • 运输方式

      冻存运输

    • 生长状态

      贴壁生长

    • 物种来源

      小鼠

    • 是否是肿瘤细胞

      0

    • 细胞类型

      胚胎干细胞

    • 细胞形态

      球形

    • 库存

      大量

    • 组织来源

      inner cell mass

    • 器官来源

      胚胎

    • 品系

      129X1 x 129S1

    Designations: R1/E
    Depositors:  A Nagy
    Biosafety Level: 1
    Shipped: frozen
    Medium & Serum: See Propagation
    Growth Properties: adherent
    Organism: Mus musculus
    Morphology: spherical colony

    Source: Strain: 129X1 x 129S1
    Organ: embryo
    Tissue: inner cell mass
    Cell Type: embryonic stem cell;
    Permits/Forms: In addition to the MTA mentioned above, other ATCC and/or regulatory permits may be required for the transfer of this ATCC material. Anyone purchasing ATCC material is ultimately responsible for obtaining the permits. Please click here for information regarding the specific requirements for shipment to your location.
    Restrictions: Prior to purchase, for-profit commercial institutions must obtain a license agreement. For instructions on how to proceed, please contact ATCC 's Office of Licensing and Business Development at licensing@ATCC .org or 703 365 2773.
    Applications: The segregation could result in several coat types, from albino, through light brown, to black, depending on the genetic background of the partner of the germline chimaera.
    The R1 cell line was established in August 1991, from a 129X1 x 129S1 3.5 day blastocyst.
    No live offspring were produced from cells older than passage #14. However, about 20% of subclones derived from passage #14 had the original developmental potential of R1 when tested by tetraploid aggregates [PubMed: 8378314].
    Pluripotency of R1 was initially tested by tetraploid embryo <-> ES aggregates for completely ES derived development [PubMed: 8378314].
    Age: 3.5 days embryo, blastocyst
    Gender: male
    Comments: The R1/E cell line was subcloned from R1 in EMBL, Heidelberg, Germany by Kristina Vintersten. The R1 cell line was established in August 1991, from a 129X1 x 129S1 3.5 day blastocyst. The cells are heterozygous for the c locus (+/c (ch)) and for the pink eye locus (+/p). This mouse ES cell line has been shown to be germline competent.In the F1 generation the coat color is uniform agouti, while in the F2 these two coat color genes segregate. The segregation could result in several coat types, from albino, through light brown, to black, depending on the genetic background of the partner of the germline chimaera.
    Pluripotency of R1 was initially tested by tetraploid embryo <-> ES aggregates for completely ES derived development [PubMed: 8378314]. They were also tested by diploid embryo <-> ES aggregates and blastocyst injection for germline transmission in chimeras [PubMed: 8361547]. At early passages (up to passage #14), one third of the completely R1-derived newborns generated by tetraploid embryo <-> R1 aggregates survived. No live offspring were produced from cells older than passage #14. However, about 20% of subclones derived from passage #14 had the original developmental potential of R1 when tested by tetraploid aggregates [PubMed: 8378314]. R1-derived animals reached adulthood and were fertile. The genetically altered lines derived from R1 gave high efficiency of germline transmission either by injecting them into C57 blastocyst or aggregating them with CD-1 or ICR outbred 8-cell stage embryos. More than 90% of the individual K.O. clones went to germline (n>60) by aggregation chimeras.
    Propagation: ATCC complete growth medium: ES-DMEM (ATCC SCRR-2010) supplemented with 2.0 mM L-Alanyl-L-Glutamine (ATCC 30-2115), 0.1 mM non-essential Amino Acids (ATCC 30-2116), 0.1 mM 2-mercaptoethanol (Invitrogen Life Technologies No. 21985), 1000 U/ml mouse leukemia inhibitory factor (LIF) (Chemicon No. ESG1107) and 15% fetal bovine serum (ATCC SCRR-30-2020).
    Atmosphere: air, 95%; carbon dioxide (CO2), 5%
    Temperature: 37.0°C
    Subculturing: Protocol: Establishing and maintaining your culture:To insure the highest level of viability, be sure to warm media to 37�C before using it on the cells.
    1. Plate mitotically arrested MEF (CF-1) (ATCC SCRC-1040 )as a feeder layer at approximately 5.0 to 6.0 X 10(6) cells/T75 at least one day before plating R1/E cells (see product sheet for mitotically arrested MEF for protocol). One hour before thawing the vial of R1/E ES cells, perform a 100% medium change using 10 ml of complete ES-DMEM (see below for recipe).
    2. Thaw the vial by gentle agitation in a 37�C water bath. To reduce the possibility of contamination, keep the O-ring and cap out of the water. Thawing should be rapid (approximately 90 seconds).
    3. Remove the vial from the water bath as soon as the contents are thawed, and decontaminate by dipping in or spraying with 70% ethanol. All of the operations from this point on should be carried out under strict aseptic conditions.
    4. Transfer the vial?s contents plus 5 ml of complete ES-DMEM to a 15 ml centrifuge tube. Use an additional 1 ml of media to rinse the vial and transfer the liquid to the 15 ml tube. Add 4 ml of complete ES-DMEM to bring the total volume to 10 ml.
    5. Spin the cells at 270 xg for 5 min. Aspirate the supernatant and resuspend the pellet in 5 ml of complete ES-DMEM.
    6. Add the 5 ml of cell suspension to the T75 flask containing feeder cells and 10 ml complete ES-DMEM.
    7. Incubate the culture at 37�C in a humidified 5% CO2/95% air incubator. Perform a 100% medium change every day, passage cells every 1 to 2 days.
    Subculturing Procedure:To insure the highest level of viability, be sure to warm media and Trypsin / EDTA to 37�C before using it on the cells. Volumes used in this protocol are for T75 flasks. Proportionally adjust the volumes for culture vessels of other sizes. A split ratio of 1:4 to 1:7 every 1 to 2 days is recommended. Plating densities should range from 3 to 4 X 10(6) cells/ T75. Note: If the colonies are close to or touching each other the culture is overgrown . Overgrowth will result in differentiation.
    1. Prepare enough flasks with MEFs as stated above in step #1.
    2. Aspirate the medium from the flask(s) with R1/E ES cells.
    3. Wash with PBS (Ca+2/Mg+2-free, ATCC SCRR-2201 ).
    4. Add 3.0 ml of 0.25% (w/v) Trypsin / 0.53 mM EDTA solution (ATCC 30-2101 ) and place in incubator. After about one minute the ES colonies will dissociate and all cells will detach from the flask.
    5. Dislodge the cells by gently tapping the side of the flask then wash the cells off with 7-10 ml of fresh culture medium. Triturate cells several times with a 10 ml pipette in order to dissociate the cells into a single-cell suspension.
    6. Spin the cells at 270 xg for 5 min. Aspirate the supernatant.
    7. Resuspend in 30 to 50 ml of fresh culture medium, depending on the split ratio.
    8. Aspirate the medium from 4 to 7 feeder layer flasks and replace it with 15 ml/flask of R1/E cell suspension.
    9. Incubate the culture at 37�C in a humidified 5% CO2/95% air incubator. Perform a 100% medium change every day, passage cells every 1 to 2 days.

    Interval: Every one to two days
    Subcultivation Ratio: A subcultivation ratio of 1:4 to 1:7 is recommended.
    Medium Renewal: Every day
    Preservation: Freeze medium: Complete growth medium supplemented with an additional 10% FBS and 10% DMSO (ATCC 4-X ).
    Storage temperature: liquid niitrogen vapor phase
    Related Products: parental cell line:ATCC SCRC-1011
    References: 57459: Matise M, et alProduction of targeted embryonic stem cell clonesIn: Matise M, et alGene Targeting: A Practical ApproachOxfordOxford University Press101-132, 1999
    71506: Nagy A, et al. Derivation of completely cell culture-derived mice from early-passage embryonic stem cells. Proc. Natl. Acad. Sci. USA : 8424-8428, 1993. PubMed: 8378314
    71870: Wood SA, et al. Non-injection methods for the production of embryonic stem cell-embryo chimaeras. Nature 365: 87-89, 1993. PubMed: 8361547
    71871: Nagy A, Rossant JProduction and analysis of ES-cell aggregation chimerasIn: Nagy A, Rossant JGene Targeting: A Practical ApproachOxfordOxford University Press177-206, 1999

    风险提示:丁香通仅作为第三方平台,为商家信息发布提供平台空间。用户咨询产品时请注意保护个人信息及财产安全,合理判断,谨慎选购商品,商家和用户对交易行为负责。对于医疗器械类产品,请先查证核实企业经营资质和医疗器械产品注册证情况。

    • 作者
    • 内容
    • 询问日期
    图标文献和实验
    相关实验
    • E-Z 96 X-press Plasmid Vacuum Protocol

      well plate inside the manifold base;    3) Place the top plate of manifold over the base, the deep well plate or waste collection tray now should be positioned under the E-Z 96 X-press Plate. Seal the unused wells of E-Z 96 Xpress Plate with sealing

    • E-Z 96 X-press Plasmid Spin Protocol

      -well plate. Transfer the cell lysate to each well of E-Z 96 X-press plate. 3. Centrifuge at 3000 x g for 5 minutes at room temperature. Discard the flow-through and re-use the deep well plate. 4. Add 500μl DLW Buffer (diluted with isopropanol

    • E. Z. N.A.TM X-press Plasmid Protocol

      实验试剂   Materials to Be Provided by User 1. Ice 2. Isopropanol (100%) 实验设备   Materials to Be Provided by User 1. Tabletop micro-centrifuge capable of 13,000 x g 2. Nuclease Free

    图标技术资料

    暂无技术资料 索取技术资料

    同类产品报价

    产品名称
    产品价格
    公司名称
    报价日期
    询价
    ATCC细胞库
    2025年11月20日询价
    ¥1500
    无锡欣润生物科技有限公司
    2025年12月13日询价
    ¥600
    上海信裕生物科技有限公司
    2025年07月14日询价
    询价
    上海康朗生物科技有限公司
    2025年07月15日询价
    R1/E
    询价