• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        LABELING MUSCLE ACTIN WITH IATR

        互联网

        1111

        Day 0 and 1

        Materials

        1.0.5 mM ATP,0.2 mM CaCl2,2 mM Tris-HCl,pH 8.0 at 4℃,250 ml for day 0 and 1000 ml for day 1.

        2.100 mM KCl,100 mM boric acid,pH 8.4 at 4℃,10 ml.

        3.IATR (tetramethylrhodamine iodoacetamide; Molecular Probes).

        4.50Ti tubes,small vial.

        Procedure (perform under reduced light,4℃ unless otherwise noted)

        1.Resuspend 10 mg lyophilized actin in 2 ml buffer 1.Be careful not to make bubbles.

        2.Add DTT (100 mM stock)to 5 mM.

        3.Dialyze against 250 ml buffer 1 overnight.

        4.Collect actin from dialysis tubing,add 100 mM KCl and 2 mM MgCl2 to induce polymerization.Let sit on ice for 20 min.

        5.Get >=1 mg IATR in a test tube.Add 100-200 µl acetone and make a fine slurry by grinding particles against the tube with a pipet.

        6.Add IATR slurry very slowly by dipping a small amount at the tip of a Pasteur pipet into 3 ml of buffer 2 in a small vial under constant stirring.

        7.Clarify in a 50Ti rotor at 40,000 rpm for 10 min,4℃.

        8.Collect clarified dye solution.Dilute 5 µl into 1 ml distilled water and measure OD at 555 nm.The OD should be in the range of 0.05 to 0.10.

        9.(optional)Calculate the volume (ml)of IATR required for reaction as 0.15 / OD or use an volume equal to that of actin.Mix gently with actin with a Pasteur pipet.

        10.Let sit on ice for 2 hr.

        11.Stop the reaction by adding DTT to 10 mM.

        12.Dialyze against 1 liter buffer 1 overnight.

        Day 2

        Materials

        1.G-25-150 column,~30x1.5 cm.

        2.Buffer 1 as for day 1,4℃,1000 ml.

        3.50Ti tubes,volumetric conical tube.

        Procedure

        1.Equilibrate G-25 column with Buffer 1.

        2.Clarify dialyzed actin in a 50Ti rotor for 1 hr at 40,000 rpm,4℃.

        3.Run supernatant through the G-25 column,collect 10 drop fractions.

        4.Collect fluorescent fractions in the void volume,measure volume in a volumetric conical tube.

        5.Polymerize actin by adding KCl to 100 mM and MgCl2 to 2 mM.Let sit for 30-60 min at room temperature.

        6.Centrifuge in a 50Ti rotor for 2 hr at 40,000 rpm,15℃.

        7.Soak pellet(s)in 0.4 ml Buffer 1 for 1-2 hr,resuspend by gentle pipeting.Sometimes there is a dark center on the surface of the pipet,which can come off as an aggregate when handled gently.Discard the aggregate by careful pipeting.

        8.Dialyze against Buffer 1 overnight.

        Day 3 on

        Materials

        1.50Ti tubes.

        Procedure

        1.Centrifuge in a 50Ti (1 hr,40,000 rpm)or 42.2Ti (30 min,25,000 rpm)at 4℃.

        2.Measure concentration and dye/protein molar ratio.Dilute 1:40 with the dialysis buffer and read the OD at 555 nm.

        D/P = {OD555 x 41 / 60,000} / {(mg/ml)/ 43,000},should be 0.5-1.1.

        3.Dilute to 3-5 mg/ml with the dialysis buffer.Calculate total mg of actin.Store as aliquots in liquid N2 after dissolving 2 mg sucrose per mg actin.

        4.Dialyze against 0.05 mM MgCl2,0.2 mM ATP,2 mM Tris-acetate,pH 6.95 overnight before microinjection.

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序