• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Use of the Hemacytometer for the Determination of Cell Numbers

        互联网

        869

        Use of the Hemacytometer for the Determination of Cell Numbers


        Counting cells by the use of a hemacytometer is a convenient
        and practical method of determining cell numbers in the case that the
        Coulter counter is out-of-order temporarily.  (It is not that bad.)  
        The hemacytometer consists of two chambers, each of which is divided
        into nine 1.0 mm squares.    A cover glass is supported 0.1 mm over
        these squares so that the total volume over each square is
        1.0 mm x 0.1 mm or 0.1 mm3, or 10-4 cm3.  Since 1 cm3 is approximately
        equivalent to 1 ml, the cell concentration per ml  will be the average
        count per square x 104.

        Hemacytometer counts are subject to the following sources of error:
        1.  Unequal cell distribution in the sample
        2.  Improper filling of chambers (too much or too little)
        3.  Failure to adopt a convention for counting cells  in contact with            
        the boundaries lines or with each other (be consistent)
        4.  Statistical error

        With careful attention to detail, the overall error can be reduced to
        about 15%.  It is assumed that the total volume in the chamber represents
        a random sample.  This will not be a valid assumption unless the
        suspension consists of individual well-separated cells.
        Cell distribution in the hemacytometer chamber depends on the particle
        number, not particle mass.  Thus, cell clumps will distribute in the
        same way as single cells and can distort the result.  Unless 90% or more
        of the cells are free from contact with other cells, the count should be
        repeated with a new sample.   A sample will not be representative if the
        cells are allowed to settle before a sample is taken.   Always mix the
        cell suspension thoroughly before sampling. 
        The cell suspension should be diluted so that each such square 
        has between 20 - 50 cells (2-5 x 10 5  cells/ml).  A total of 
        300 - 400 cells should be counted, since the counting error is approximated
        by the square root of the total count.   A common convention  is to
        count cells that touch the middle lines (of the triple lines) to the
        left and top of the square, but do not count cells similarly located 
        to the right and bottom.
        Hemacytometer counts do not distinguish between living and dead cells. 
        A number of stains are useful to make this distinction.  Trypan blue
        among others  (Erythrosin B, Nigrosin) can be used: the nuclei of damaged
        or dead cells take up the stain.  If more than 20% of the nuclei are
        stained, the result is probably  significant.  Although the trypan stain
        distinction has been questioned, it is simple and gives a good approximation.

        Materials
        1.  Clean hemacytometer and cover glass, or cover slips
        2.  Pasteur Pipets or Transfer Pipets
        3.  Balanced Salt Solution (BBS) or PBS
        4.  Trypan blue, 0.4% in BBS (or PBS)
        5.  Microscope
        5.  Tubes
        6.  Hand counter (Colony counter can be used)
        7.  Cell suspension 

        Procedure
        1.  Dilute 0.2 ml of Trypan blue with 0.8 ml of BBS.
        2.  Place cover glass over hemacytometer chamber.
        3.  Transfer 0.5  ml of agitated cell suspension  to a 15 ml tube
        and add 0.5 ml of diluted trypan blue.
        4. With a Pasteur or transfer pipet, fill both chambers of the
        hemacytometer (without overflow) by capillary action.  Cells will
        settle in the tube and in the pipet by gravity within a few seconds. 
        Work quickly.
        5.  Using the microscope with a 10X ocular (and a 10X objective),
        count the cells in each of  10 squares (1 mm2 each).  If over 10% of
        the cells represent clumps, repeat entire sequence.  If fewer than
        200 or more than 500 cells are present in the 10 squares, repeat with
        a more suitable dilution factor.
        6.  Calculate the number of cells per ml, and the total number of
        cells,  in the original culture as follows:
        Cells/ml = average count per square x 104
        Total cells = cells per ml X any dilution factor X total volume of
        cell preparation from which the sample was taken.
        7.  Repeat count to check reproducibility (+/- 15%).

        References
        1.  Berkson, J., T. B. Magath and M. Hurn (1939).  Am. J. Physiol. 128, 309.
        2.  Sanford. K.K., W.R. Earle, V.J. Evans, H.K. Waltz and J.E. Shannon (1951).
        3.  Absher, M. in Tissue Culture Methods and Applications, Eds. Kruse, P.F. and Patterson, M.K., Jr. Academic Press, N.Y., 1973, p.395.


        From the Laboratory of Dr. Allan Bradley                        
        Baylor College of Medicine, Houston, Texas

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序