• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Immunoprecipitation of metabolically labeled cells

        互联网

        1073

        Immunoprecipitation of metabolically labeled cells 

         

        <center> (Protocol from An Zhou, Johns Hopkins, 1995)</center>

         

         

        1. To your sample, add Super E, protease inhibitors, 1 mM cold Met, antibody. 
        TMT extract or medium - dilute with Super E to convenient volume; add protease inhibitors, cold Met and antibody.

        Some antibodies work only after the antigen has been denatured (e.g. Ab 877, Ab 471): to 50 ul of sample in TMT, add 5 µl 10% SDS and incubate at 100 o C for 5 min; allow to cool to room temperature for 5 min; add IN THIS ORDER: 25 µl 15% NP-40, 180 µl Super E, 3 µl PMSF, 3 µl inhibitor mix, 10 µl antibody. Super E: 50 mm phosphate, 1% Triton.

        2. Allow antibody to bind overnight at 4 o C (4 h is sufficient for 
        some antibodies).

        3. Spin samples 3 to 5 min in hot microfuge at top speed.

        4. While samples are spinning, number a new set of tubes; add as much Super E as you can (at least 0.5 ml) and 60 µl Protein A agarose slurry (1:3) for 10 µl antiserum.

        5. Transfer supernatant to new tube with Protein A; do not be greedy and take every last bit of supernatant - you will get dirty IPTs.

        6. Shake 60-90 min at room temperature; do not go much longer than this.

        7. Wash beads: spin 10 sec in hot microfuge - wash 3 X in SuperE and 2 X in PB. Invert tubes to resuspend beads for each wash.

        8. Resuspend beads in SDS samples buffer (60 µl for slab gels; 105 µl for tube gels) with blue or pink tracker dye - DO NOT PUT HOT PIPETTES INTO 15 ml TUBES - YOU WILL END UP WITH HOT SAMPLE BUFFER.

        9. Immediately (not a few minutes later) boil samples for 5 min.

        10. Allow to come to room temperature; spin to collect liquid.

        11. Count aliquot (2 or 5 µl).

        12. Load gels: slab gels: 50 mV overnight - leave a note on board if you want gels checked in am

        180 mV maximum during day- 4-5 h 

        tube gels: 20 mV overnight

        50 mV maximum during day

        13. Slab gels - 30 min in preamplify; 30 min in Amplify/Enhance

        14. Dry gel - check/empty trap before you dry gel; 90 min at 70 o C is usually enough.

        15. Tube gels - elute slices overnight in SDS gel elution buffer; squirt; count

         

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序