优越的光泽度和高透明度
- Unique bluish shade gives fresh appearance to the film and
独特的带蓝色阴影给您薄膜外观上强烈的冲击
Thus when you use Bilcare film, your product enjoys higher visibility and appeal
因此当您使用保凯的薄膜,您的产品将会拥有更高的清晰度
-Bilcare Exxtra has density of 1.33-1.34 g/cc
保凯Exxtra的密度是1.33-1.34g/cc
as against conventional PVC film with 1.38-1.40 g/cc
常规的PVC薄膜的密度是1.38-1.40 g/cc
- Bilcare Exxtra is manufactured using uniquely formulated PVC with high chemical purity confirming to pharmaceutical requirement with lowest RVCM content
保凯Exxtra使用高化学纯度的独特的PVC辅料生产,是医药行业要求使用的低RVCM物质
- No chemical fillers are added resulting in film with incomparable density ratio
没有添加化学填充剂,因此薄膜具有不可相比的密度率
The difference provides 3.5% extra yield and therefore more number of blisters
制作的不同产生了3.5%的产量区别,因此有更多的泡罩
- 90% of Bilcare consignments are without joints,
while 2-3 joints are normally acceptable
保凯90%的发货是没有接合点,其它也仅有2~3个接合点属于正常可接受范围
- Every joint causes 1-2 meters film
在生产中每一接合点将会浪费1-2米的薄膜
This saves material upto 0.5%
这将会节省0.5%以上的材料
•Tensile strength is the measure of the toughness of the film and minimum requirement is 400 Kg/m2.
抗张强度是衡量薄膜刚性的方法，薄膜对此的最低要求是400kg/m2
•Higher tensile strength, higher the toughness but difficult to thermoform
抗张强度越高，刚性也就越高，也越难以成型
•Standard Blister films has tensile strength of 550 Kg/m2 and above.
标准的泡罩薄陌的抗张强度一般都在550 Kg/m2以上
•Bilcare films are having optimum tensile strength of ~450 Kg/cm2 which facilitate smooth thermo-formation at comparatively lower temperatures.
保凯薄膜具有最适宜的抗张强度~450 Kg/cm2 ，需要的成型温度更低，成型得更光滑
•OTS ensures uniform thinning of the film during blister formation and better barrier property of the pack.
适宜的抗张强度确保泡罩成型过程中薄膜的厚度均匀，具有更好的保护性
Film thickness uniformity
薄膜厚度均匀
• Internationally accepted norm for thickness variation in the PVC blister film is 5%.
国际上对于PVC泡罩薄膜的厚度可接受的波动是5%
•Sophisticated controls and measures during the calendaring process, Bilcare film has thickness less than 3%. This facilitates the smooth blister formation at optimum thermoforming parameters with consistent results in all the pockets formed.
经过多年的经验累积，通过多年的调控，保凯薄膜的厚度波动范围已经可以控制在3%以内。这使得泡罩的成型在最适宜的成型参数下更光滑，成品一致性更高。
•Locally available standard films have thickness variation between 7 –10%, creating inconsistency and wastage during production
某些地方性的薄膜，其厚度波动在7~10%，导致成品不够一致性和浪费。
更好的机器加工性能可带动相关的节约
•Wastages in the lid foil封盖的损耗
•Wastage of man hours 人力资源的损耗
•Wastage of machine time 机器时间的损耗
and most important更重要的是
•Wastage of raw material!原料的损耗
•
Even a 1% savings in the wastage of medicine, the cost implication is equivalent to 9% savings in the packaging cost.
•即使1%的药物损耗，其价值最少相等于9%的包装损耗
文献和实验
技术资料