Drummond微量注射器

充灌速度	Fast	46 nL per second
	Slow	23 nL per second
注射速度	Fast	46 nL per second
	Slow	23 nL per second
倒空速度	Fast	230 nL per second
	Slow	92 nL per second

Nanoject II Auto-Nanoliter Injector

• Automated microprocessor controlled Microinjection Pipet delivering precise nanoliter volumes accurately
• Remote control and non-rotating plunger eliminates vibration allowing precise injection minimizing possible cell rupture
• Selectable Injection Volumes: from 2.3 nanoliters to 69.0 nanoliters in 16 increments
• Selectable Operating Speeds:

  Fill Speed	Fast	46 nL per second
  	Slow	23 nL per second
  Injection Speed	Fast	46 nL per second
  	Slow	23 nL per second
  Empty Speed	Fast	230 nL per second
  	Slow	92 nL per second

• Supplied with sufficient borosilicate glass capillaries for preparing 400 injection tips, standard softening point 780°C
• Can be mounted on most micromanipulators
  Note: Universal Adapter 3-000-024-A supplied with unit
• Separate Foot Switch available to allow hands-free operation

Each Nanoject II Auto-Nanoliter Injector comes complete with 200 borosilicate capillaries that can be pulled to the required tolerance together with a back filling needle and maintenance kit.

Catalog Information

Cat. No.	Description
3-000-204	Nanoject II Variable Volume (2.3 to 69 nL) Automatic Injector with Glass Capillaries (110V)
3-000-205A	Nanoject II, 220V, CE, Euro
3-000-206A	Nanoject II, 220V, CE, UK

Note: Universal Adapter supplied with all the above units

Replacement Parts

Cat. No.	Description
3-000-002-KN	O-Ring kit for Models 204, 205A, and 206A includes: 1 collet, 1 small O-Ring, 1 spacer, 1 compression O-Ring, and 1 Allen wrench
3-000-027	30 gauge, 2" Backfilling Needle
3-000-000-203-X	Pointed Plunger Wire

Replacement Glass Capillaries

Cat. No.	O.D (mm)	Length	I.D. (mm)	Pack
3-000-203-G/X	1.14	3.5"	0.53	100
3-000-203-G/XL	1.14	7"	0.53	100

This equipment is ready for use as received. It does require pulled capillary tips. It is essential that only the capillaries supplied or exact replacement capillaries are used for pulling micropipets.

Contents:

• a. Injector head with cord.
• b. Control box.
• c. Power supply with cord.
• d. Capillary glass; 2 vials of 100 pieces per vial:

1.( 3.5" capillaries, 100 pcs. (Cat. No. 3-000-203-G/X)

2.(7.0" capillaries, 100 pcs. (Cat. No. 3-000-203-G/XL)

• e. Replacement O-ring kit with collet, standard. (Cat. No. 3-000-002-KN)
• f. 1 Allen wrench for replacing wire plunger.
• g. 1 30g x 2" needle for backfilling pipets. Cat. No. 3-000-027

Operation:

The injector head should be mounted in a suitable micromanipulator or stereotaxic unit. Marzhauser model MM33 is quite suitable and frequently used. The aluminum barrel with the Drummond logo, provides an ideal clamping surface. Its diameter measures 11mm.The precise operation of the Nanoject II depends greatly on the use of tips prepared from the glass provided. We cannot guarantee that glass micropipets pulled from capillaries with other dimensions will work. Never attempt to use micropipets pulled from filament glass. Damage to the wire plunger will result and injection volumes will not be accurate.

Micropipet Pulling and Backfilling

The Nanoject II requires the use of pulled micropipets from the glass provided. Ideally, the tip size should be 10-30 microns in size. The capillary glass provided is produced from N-51-A material and has a softening point of 780º C. Many researchers pull the tips and then break them off with forcepts. This enables piercing the cell membrane much easier with no skipping. Once the tips are pulled, they must be "backfilled" with oil (or other non-compressible fluid) before attachment to the injector. Silicone or mineral oil is frequently used. Backfilling is facilitated by using the 30g x 2" needle and a syringe. Disposable spinal needles are also frequently used.

NOTE: THE NANOJECT II WILL NOT OPERATE PROPERLY WITHOUT BACKFILLING THE MICROPIPET.