• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Spotted Microarray Hybridization and Scan

        互联网

        1275

         

        Note: for single spotted arrays halve volumes
        • Mix two color samples (for genomic DNA, Normally 0.5ug), add 2ml Block Mix (10mg/ml salmon sperm DNA (BRL) + 4mg/ml yeast tRNA)
        • Use Speed Vec to dry the sample to a small volume, normally less than 5ml, do NOT overdry.
        • Add 50ml Sigma ArrayHybTM Hybridization Buffer
        • Heat mixture to 100°C 5 minutes, mix by pipetting up and down if necessary
        • Spin for 5 minutes at 14,000 RPM to pellet any particulate material
        • Place the Microarray(s) in a hybridization chamber (TeleChem or GeneMachines)(To prevent arrays from drying, seal array in hybridization chamber with Whatmann paper moistened with 100 ml of H2 O.)
        • Carefully transfer the probe solution to a new tube avoiding any pelleted material.
        • Carefully pipette the hybridization mix onto the array (between marks etched on back of array)
        • Overlay with a clean glass cover slip being careful to avoid bubbles under the cover slip
        • Seal chamber and place in 60°C water bath. Incubate 18-20 hours

        Wash Slides

        • Dry the exterior of hybridization chamber
        • Carefully open hybridization chamber to avoid H2 O entering the chamber.
        • Remove slide from the chamber and quickly place the slide, array side down, in a container filled with 0.2X SSC, 0.03% SDS and a slide holder. Position the slide upside down and at a slight angle so the coverslip falls away from the slide. Keep slide in this position until the coverslip has fallen off.� When cover slip falls off, transfer the slide to the other wash chamber containing wash buffer 1 and incubate for 5min at room temperature with gentle mixing on an orbital shaker (speed 3-4).
        • Transfer ONLY the slide to a container with 0.2X SSC (filtered) and a slide holder. Incubate for 5min at room temperature with gentle mixing on an orbital shaker (speed 3-4).
        • Transfer the slide holder with the slide to fresh 0.2X SSC (filtered) and repeat wash 5min.
        • Transfer the slide holder with the slide to 0.05X SSC (filtered) and wash for 45 sec.
        • Spin in slide holder seated in a Plexiglass carrier on microtiter plate carrier for 5 minutes at 500 RPM to dry slide.
        • Scan slide.

        Scan Slides

        Currently we use Packard Science SA5000 scanner to scan our microarrays. to obtain good signal and low signal/noise, different PMT setting might be used. However, to compare probe quality and hybridization quality, it is suggested to scan all slide at the same power and PMT setting. Now we use the setting:

        • For Cy3, which normally is the RNA channel, Power 85, PMT 75.
        • For Cy5, which normally is the genomic DNA channel, Power 85, PMT 70.

        Reagents and Suppliers

        Hybridization Chambers Telechem Cat # AHC-1
        ArrayHyb Buffer Sigma Cat # A-7718

         

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序