• 我要登录|
  • 免费注册
    |
  • 我的丁香通
    • 企业机构:
    • 成为企业机构
    • 个人用户:
    • 个人中心
  • 移动端
    移动端
丁香通 logo丁香实验_LOGO
搜实验

    大家都在搜

      大家都在搜

        0 人通过求购买到了急需的产品
        免费发布求购
        发布求购
        点赞
        收藏
        wx-share
        分享

        Dropout plates for yeast

        互联网

        1316

         

        Materials

        (Solutions are all available from the media room)

        • 200ml bottle of 2x SD
        • 200ml bottle of 4% agar -- make sure to sign it out
        • 40% glucose
        • CSM minus the relevant marker(s), as powder
        • Stack of plates (above the -20 freezers)

        Yeast growth medium generally consists of three parts: a nitrogen base (supplied by SD), a sugar source (supplied by glucose) and necessary amino acids (supplied by CSM). These three components are what you''re going to mix together and then add to agar to make plates.

        Making amino acid dropout (CSM) solution

        Generally easiest to make a 10x master solution that you can dilute back when you''re pouring plates. Let''s assume you''re going to make 200ml of a 10x master solution:

        1. Grab a 500 ml conical flask
        2. Figure out how much of your dropout powder you''re going to need and weigh it out
        3. Dump CSM into conical flask and fill it up to 200ml mark with deionized water (from white tap above the sink)
        4. The CSM will need a bit of help dissolving, so put in a stir bar (rinse it off first with dI water) and put it on a stirrer for 1-2 hours (speed around 6-7, heat 3-4).

        Once the CSM has gone into solution, you''ll need to filter-sterilize it:

        1. Get a 200ml orange screwtop bottle and a vacuum filter
        2. Flame the bottle & top, remove the filter from its packaging and screw it onto the bottle. The filter is sterile, so try not to touch it to anything else
        3. Attach the adapter to the filter and the vacuum nozzle to the adapter (vacuum should be off)
        4. Pour the CSM solution into the top of the filter
        5. Turn on vacuum and allow the solution to get sucked through the filter and then turn off the vacuum
        6. Unscrew the filter, flame the bottle and top again, recap it and label it.
        • here to make DO stocks from individual amino acids.

        Mixing growth medium

        1. Add 20ml of 40% glucose and 40ml of 10x CSM solution to 200 ml of 2x SD
        2. Heat up mixture to 65 degrees in water bath

        Preparation of LB Agar

        1. Melt in microwave:

        Making agar-growth medium mix

        1. Mix agar and growith medium pouring the growth medium into the agar bottle -- no need to cool down the agar first, it gets cooled by mixing with the growth medium
        2. Swirl gently to mix, put in water bath for a bit until bubbles disappear

        Actual Pouring

        1. Using sterile technique (flame the top of the bottle) pour the agar mixture into the plates.
        2. Recap each plate upon pouring. If there are lots of bubbles in your plates (i.e., more than one or two on the edge), you can flame the plate using the small bunsen burner to eliminate bubbles. (See a demo on this). Another way to remove the fine bubbles that may be in your flask before puring is to mist the inside of the flask with a 75% ethanol spray bottle.
        3. Leave plates to dry and cool for a while (overnight even).
        4. Store the plates in their original bags - upside down, so that the gel is hanging downwards (this keeps condensation off the gel).
        5. Label the bags, using correct color tape for the dropout medium
        6. Put bags in a refrigerator

         

        ad image
        提问
        扫一扫
        丁香实验小程序二维码
        实验小助手
        丁香实验公众号二维码
        扫码领资料
        反馈
        TOP
        打开小程序